Skip to content
Design free

Frame and roof

Metal Trusses for Pole Barns: Steel vs Wood, Priced

Steel pole barn trusses go up 10 to 12 ft apart on 6x6 posts and cost two to three times a wood truss of the same span. Here are the listed prices by span, the loads the stock trusses are rated for, and the 30x40 truss line worked both ways.

By The Barn PlannerUpdated 11 min readChecked against 11 sources

Metal trusses for a pole barn: welded angle iron steel gable trusses on 6x6 wood posts 10 ft apart, wood purlins across them and the first steel roof panels onIllustration

The short answer

Metal trusses for a pole barn are welded angle iron gables set about 10 ft apart on 6x6 posts. Listed prices run $452 to $577.50 for a 30 ft steel truss against $120 to $330 for wood. A stock steel truss we read is rated for 15 psf of ground snow at 10 ft centers, so check your snow load before you buy.

Metal trusses for a pole barn are welded steel gable trusses, usually angle iron, that sit on wood posts about 10 ft apart and carry wood purlins and a steel roof. They replace the wood trusses of a classic post-frame building, and three things change when you make the swap: the price of each truss, the spacing of the posts and the snow load the roof is rated for.

This guide puts numbers on all three. The steel truss prices come from three sellers’ published lists, the wood figures from the price range our barn designer uses and a stock price list, and the frame counts from the designer’s own 30x40. We design wood truss pole barns, so read our side of the comparison with that in mind; the steel sources are named next to every figure.

What Metal Pole Barn Trusses Are

A steel pole barn truss is a triangle of steel angle, with a top chord, a bottom chord and webbing between them, welded in a shop and delivered whole. Best Buy Metals1 describes its trusses as angle iron, 1-1/2 x 1-1/2 in or 2 x 2 in for the chords depending on the span and 1-1/4 x 1-1/4 in for the webs, built by certified welders and engineer stamped for five southern states.

On a post-frame building the truss does the same job as a wood one. It spans the full width from sidewall to sidewall and lands on a pair of posts. The difference is how many of them there are and how much each one carries.

Gable, Lean and Header Trusses

Steel truss sellers sell three shapes. A gable truss is the common two-slope truss. A lean or shed truss has one slope, for a lean-to or a single-slope building. A header truss, or bar joist, runs along the sidewall between posts and carries a truss that lands where no post is. Stroud’s lists all three, and Summertown Metals3 lists 20 and 24 ft steel bar joists for 6x6 posts “up to 40’ trusses”.

What Comes With Them

The truss is only the roof frame. Most steel truss packages still use wood purlins on top and wood girts on the walls, and posts that you buy and set yourself. Best Buy Metals1 includes a hardware kit with each order and says a 6x6 structural post is required. It also warns that the trusses ship on a truck that needs offload equipment on site, and that orders over 11 trusses may need a different shipping option.

Metal Trusses for Pole Barn Prices by Span

Here are the listed prices per truss, as printed, beside the wood range our designer uses for the same span. Read the date on each column: steel prices move with the steel market, and none of these includes freight or tax.

Span Best Buy Metals, steel (Oct 13, 2026) Stroud’s, steel (Nov 20, 2026) Summertown Metals (Oct 13, 2026) Wood truss range (HomeGuide, Jan 2026)
20 ft $342 $385 $90 to $250
24 ft $371 $462 $100 to $300
30 ft $452 $577.50 $153.60, wood, 4/12, stock $120 to $330
36 ft $693 $439.83, steel, 4/12, for 6x6 posts $250 to $400
40 ft $568 $770 $203.52, wood, 4/12, stock $280 to $500
50 ft $962.50 $300 to $790
60 ft $1,155

Stroud’s also prices a 20 ft header truss at $800 and a 24 ft at $960, and says trusses not in stock take 6 to 8 weeks. Its page tells the buyer to check the local building codes before purchasing. Summertown Metals3 marks its 36 ft steel gable as non-stock.

Why Steel Costs More per Truss

A truss for truss comparison is not quite fair to steel, because a steel truss is built to sit farther apart. Best Buy Metals1 designs its stock gables for 10 ft centers. Wood trusses in post-frame work are most often 4 to 10 ft apart (NFBA5, Frame Builder, 2022), and our designer draws them on 6, 8 or 10 ft bays. Fewer trusses at a higher price per truss is the steel trade.

Freight Is Its Own Line

Steel trusses are made in a few plants and trucked to you. Hansen Pole Buildings6, which makes its own wood trusses, says the steel trusses it once sourced came from Tennessee with a second freight bill on top, and that without the freight the two would cost roughly the same (Hansen, 2024, a secondary source from a wood truss seller). Ask every steel quote for the delivered price to your ZIP code.

The 30x40 Truss Line, Worked Both Ways

Here is what the truss line comes to for one real building. Our free 30x40 pole barn plan has a 30 ft span on 8 ft bays. Redrawn on 10 ft bays, the spacing steel trusses are designed for, the same barn changes like this:

Wood trusses, 8 ft bays Wood trusses, 10 ft bays Steel trusses, 10 ft bays
Trusses 6 5 5
Price per truss $120 to $330 $120 to $330 $452 to $577.50
Truss line $720 to $1,980 $600 to $1,650 $2,260 to $2,887.50
Posts 3-ply 2x6 Southern Pine No. 2 post, nail-laminated, treated UC4B 3-ply 2x8 Southern Pine No. 2 post, nail-laminated, treated UC4B 6x6 or larger
Purlins 2x6 on edge at 24 in 2x8 on edge at 24 in per the truss maker

All three columns are at 30 psf of ground snow, a 10 ft eave and a 4/12 roof. The steel column multiplies the Best Buy Metals1 and Stroud’s list prices by the truss count, before freight. The wood columns use the HomeGuide4 range that the designer’s cost panel uses, and the truss maker quotes the final figure for either.

A 30x40 pole barn frame on four 10 ft bays, the spacing metal trusses for a pole barn are designed for, with a truss on every pair of posts
Four 10 ft bays. the 30x40 redrawn at steel truss spacing, 5 trusses, one on every pair of posts.Open this design

What the Wider Bay Costs Elsewhere

The truss count drops by one, but every purlin and girt now spans 10 ft instead of 8, and every post carries a wider strip of roof. In our designer the 30x40 on 10 ft bays moves its posts up to 3-ply 2x8 Southern Pine No. 2 post, nail-laminated, treated UC4B, and its purlins to 2x8 on edge at 24 in, and its materials total comes to $18,301 against $17,525 on 8 ft bays with wood trusses. The truss spacing guide has the full chart for 6, 8 and 10 ft bays at three snow loads.

A 40x60 at Steel Spacing

At 40 ft the gap narrows a little. Our 40x60 pole barn plan uses 11 wood trusses on 6' bays. On 10 ft bays the same footprint would take 7 trusses: at $568 to $770 each that is $3,976 to $5,390 in steel, against $280 to $500 per wood truss for the trusses drawn. Price both before you choose, and ask the wood truss maker to quote 10 ft bays too.

Snow and Wind: Read the Rating Before the Price

This is the line that decides most steel truss questions. Best Buy Metals1 rates its stock steel gables for a 20 psf roof live load and a 15 psf ground snow load at 10 ft centers, with a 105 mph design wind speed under the 2018 and 2021 IBC. That is a light rating. Our example designs start at 30 psf of ground snow, and the designer takes the snow and wind for your site.

What Happens Past the Rating

A truss rated for 15 psf is not a truss for a 40 psf county. You need a truss engineered for your load and your spacing, and the price of that truss is a different number from the stock list. Hansen Pole Buildings6 writes that most steel trusses are not engineered to carry snow loads and are generally seen only in regions with little or no snow (Hansen, 2024 and 2025). Hansen sells wood trusses, so weigh that, but the Best Buy Metals1 rating above says the same thing in the seller’s own words.

Ask for the Sealed Drawing

Wood or steel, the truss maker designs the truss for a span, a spacing and a load, and the truss design drawing is usually sealed by a professional engineer registered in your state (NFBA5, Frame Builder, 2022). Larimer County8, Colorado asks for the stamped truss design at inspection. A steel truss without a drawing for your loads gives the building department nothing to approve.

Confirm before you continue

The rating on the truss drawing matches your county

Before you order, get the steel truss’s ground snow load, wind speed and spacing in writing and compare them with your county’s design loads. If the county asks for more than the stock rating, ask for an engineered truss or go back to wood.

How Far Apart Metal Trusses Go

Steel trusses sit 10 or 12 ft apart, one on each pair of sidewall posts. Best Buy Metals1 designs its gables for 10 ft. Hansen Pole Buildings6 writes that most steel trusses are designed to be placed every 10 or 12 ft, directly aligned with the eave sidewall columns, and Lyon Metal Roofing9 gives the same 10 or 12 ft as typical, adjusted for load (both secondary sources).

The Posts Follow the Trusses

Whatever the truss, it lands on a post or on a header. Clermont County10, Ohio writes that trusses must be spaced to align with the post intervals, and Clark County11, Ohio that truss spacing aligns with the posts or uses truss girders. So a steel truss at 10 ft means posts at 10 ft, and that is a wider bay than the 8 ft most wood post-frame barns use.

Our Designer Stops at 10 ft

Our designer draws 6, 8 and 10 ft bays. A 12 ft bay is outside what it draws, for the posts and girts as much as for the trusses, so a 12 ft steel layout needs the steel maker’s engineering for the whole frame. For a 10 ft layout, the designer gives the posts, footings, girts, purlins and steel panel by panel at that spacing; the trusses on its order sheet are wood.

Steel or Wood Trusses: When Each One Wins

Neither material wins everywhere. The numbers above point to a short list.

When Steel Makes Sense

  • Low snow, long spans. In a county with little or no snow, a stock steel gable on 10 ft bays can carry a wide roof with fewer trusses to lift.
  • Rot and fire worry you more than price. Steel does not rot, and Lyon Metal Roofing lists faster install and durability as the reasons to choose it.
  • The kit already includes them. If a steel truss kit is priced as a whole building, compare the whole building, not the truss line.

When Wood Makes Sense

  • Snow above the stock rating. Wood trusses are designed for your snow load and spacing by the truss maker as a matter of course.
  • You want the truss checked with the frame. Our designer sizes the posts, the truss bolts and the bearing for a wood truss at your loads; with steel, that connection is the steel maker’s detail.
  • You want the cheapest roof frame. In every row of the price table, the wood range sits below the steel list price for the same span.

Either Way, Three Quotes

Send the same building to a steel truss seller and a wood truss maker: span, pitch, overhang, spacing, ground snow and wind. The plan from our designer includes a truss order sheet with those values for the barn you drew. Compare the delivered prices and the rated loads, then lay out the posts to the drawing you pick.

Ordering Metal Trusses for a Pole Barn

  1. Draw the barn at 10 ft bays

    Set the width, the length in 10 ft bays, the eave and your loads in the designer, so the posts and footings are sized for that spacing.
  2. Ask for the rating

    Ground snow, roof live load, wind speed and spacing, in writing, for the span you need.
  3. Ask for the delivered price

    Freight, the hardware kit and how the truck unloads.
  4. Match the posts

    Best Buy Metals asks for 6x6 posts. Check the post size the designer gives against the steel maker’s connection detail.
  5. Get the drawing for the permit

    The pole barn permit guide covers what the building department asks for.

Safety

Lifting steel trusses

A steel truss is heavier than a wood one of the same span and arrives on a truck that needs equipment to unload. Lift each truss with the equipment the seller specifies, brace it as it goes up, keep people out from under it and stop in wind.

Wood Trusses Instead

If the snow load or the price rules steel out, the truss spacing guide covers wood trusses on 6, 8 and 10 ft bays, and the pole barn cost guide prices the whole 30x40 line by line. Next: how to build a pole barn for where the trusses go in the build order.

Sources

Every number in this guide that does not come from our own barn designer was checked against these 11 documents, numbered in the order the text first cites them and read between Oct 13, 2026 and Nov 20, 2026. 4 are county guides, handbooks and makers; 7 are secondary sources (price guides and sellers' pages), marked, used only where no store or maker gives a number.

  1. 1Best Buy MetalsSecondary sourceSteel Gable Trusses (product page and store catalog) (Oct 13, 2026)
  2. 2Stroud's Building SupplySecondary sourceSteel Trusses (price list)
  3. 3Summertown MetalsSecondary sourcePublic price list, trusses (Summertown, Tennessee and Hayden, Alabama stores) (Oct 13, 2026)
  4. 4HomeGuideSecondary sourceRoof truss prices (Jan 21, 2026)
  5. 5National Frame Building Association, Frame BuilderTruss, But Verify, B. Bolduc, PE, SE (Aug 2022)
  6. 6Hansen Pole BuildingsSecondary sourceSteel trusses (Pole Barn Guru blog posts, 2013 to 2025) (Mar 11, 2025)
  7. 7Hansen Pole BuildingsSecondary sourceTrusses: Steel or Wood? (Pole Barn Guru blog) (Sep 24, 2024)
  8. 8Larimer County, ColoradoPrescriptive Design for Pole Barns (Mar 1, 2022)
  9. 9Lyon Metal RoofingSecondary sourceWhy Choose Steel Trusses for Your Pole Barn (and Not Just Wood)
  10. 10Clermont County, OhioPost Frame Construction Guide, RCO 328 (rev. Dec 17, 2025)
  11. 11Clark County, OhioPole Building Section (RCO 328 summary) (rev. Oct 31, 2022)

Questions

Anything else? Write to us or browse every guide.

Questions people ask

Usually not, truss for truss. A 30 ft steel truss lists at $452 at Best Buy Metals and $577.50 at Stroud's, while the published range for a 30 ft wood truss is $120 to $330. Steel can claw some of that back with wider spacing and fewer trusses, but the posts get bigger, so price the whole frame.

From about $342 for a 20 ft span to $568 for 40 ft at Best Buy Metals (prices read Oct 13, 2026), and $385 to $770 at Stroud's, with 50 ft at $962.50 and 60 ft at $1,155. Freight, a hardware kit and the unloading equipment can sit on top of those figures.

Usually 10 or 12 ft on center, one truss on each pair of sidewall posts. Best Buy Metals designs its stock steel gables for 10 ft centers, and Hansen Pole Buildings and Lyon Metal Roofing both give 10 or 12 ft as the usual spacing. The truss maker's engineering for your loads sets the real figure.

Low snow ratings on stock trusses, heavier posts, freight from a distant plant and uneven quality control. A stock gable we read is rated for 15 psf of ground snow at 10 ft centers, and Hansen Pole Buildings, which sells wood trusses, writes that many welded steel trusses are not engineered for snow at all.

A 30 ft wood truss runs $120 to $330 in the HomeGuide range we use, and Summertown Metals listed a stock 30 ft 4/12 wood truss at $153.60 in October 2026. A 30 ft steel truss lists at $452 at Best Buy Metals and $577.50 at Stroud's. Your snow load and spacing can raise either quote.

Stock steel pole barn trusses commonly run from 12 to 60 ft: Stroud's lists gables up to 60 ft and Best Buy Metals up to 40 ft. Lyon Metal Roofing says its supplier offers trusses up to 100 ft wide depending on pitch. Past 40 ft, ask for the truss's rated snow load and spacing in writing.

Yes, that is the usual setup. Best Buy Metals sells its gable trusses for 6x6 structural posts with a hardware kit, and Summertown Metals lists its steel gables and bar joists for 6x6 posts. Our designer draws the wood posts, girts and footings, but it does not draw or check the steel truss connection.

Design it, then build it

Size it for your loads before you buy a post.

Draw your barn in 3D for your snow, wind and frost line. The posts, the trusses, the purlins and the priced materials list follow every change. Free, no account.

Design my barn, free
Designing
Free
Builder's plan
$79 once
Account
Not needed
Inside a new pole barn built the way our metal trusses for pole barn guide describes: trusses, girts and a workbench, the overhead door open on a fieldIllustration