2 free starting plans
Pole barn lean-to plans
2 free pole barn plans with an open lean-to along the long wall, for a tractor, firewood or a trailer: the 24x32 and the 30x40. The lean-to has its own posts, a ledger on the main wall and a steel roof, and the designer checks its clear height and the posts that carry it.

- Plans
- 2
- Floor, sq ft
- 768 to 1,200
- Materials, about
- $17,100 to $21,800
- Preliminary checks
- All passed at 30 psf
Every size, drawn by the designer
Pick a pole barn lean-to size.
Each one is a full starting plan: framed, checked for 30 psf of ground snow, 115 mph of wind and a 36 in frost line, and priced. Switch the view to see the frame or the dimensions.
30x40
30x40 pole barn
A 30x40 garage on 12 ft walls with an open 12 ft lean-to along the right side for equipment, firewood or a trailer.
- Floor
- 1,200 sq ft
- Eave
- 12'
- Overhead door
- 10' x 8'
- Posts
- 25, 3-ply 2x8
- Trusses
- 6 at 8', 30' span
- Bays
- 5 of 8'
Preliminary checks passed for the loads you entered. Local approval not checked. 7 items for your builder or engineer: snow drift on the lean-to, posts carrying it, window jack studs on the girts, post foundation in uplift, post tops dry when bolted, diaphragm, shear walls and post embedment, wall diagonal braces.
Materials about $21,800, before tax and delivery
What it needs
What a lean-to has to get right.
The lean-to roof sits under the main eave and rides on the main wall. Here is what that changes.
01Frame
Its own posts, hung on a ledger.
Each lean-to is 12 ft wide along the right side, open, at 3/12. The designer takes 8 to 14 ft wide at 3/12 or 4/12, with the lean-to roof tucked 6 in under the main eave. It sits on its own posts on the main bay lines, with a rafter on each post line bolted to the main post over a ledger pair, and purlins on edge like the main roof.
The main posts carry extra load from the lean-to, so the designer checks them and the pad under them, and lists what it cannot calculate.
02Clear height
The outer eave is the lowest point.
The lean-to roof slopes down from the main wall, so its outer eave sets the clear height. On the 30x40 it is 8' 6" and on the 24x32 8' 6". The designer asks for at least 6' 8" of clear height under the outer eave and notes that under 8 ft is too low for a pickup. To get more, raise the main eave, make the lean-to narrower or use a steeper pitch.
03Snow drift
A lean-to under a higher roof collects snow.
Snow slides and drifts from a higher roof onto a lower one beside it, so a lean-to under a barn eave can carry more snow than the ground snow load. This planner does not calculate that drift: it lists it for the lean-to framing to be designed for it, and the county prescriptive pole barn guides we read leave lean-tos out of their tables. In snow country, have the lean-to rafters and the main posts checked before you build.
Side by side
Both pole barn lean-to plans compared.
| Plan | Floor | Eave | Vehicle door | Posts | Trusses | Materials, about | Labor if hired, broad reference | Build time | Checks |
|---|---|---|---|---|---|---|---|---|---|
| 768 sq ft | 12' | 8' x 8' overhead | 19 | 5 at 8' | $17,100 | $3,840 to $11,520 | 135 to 195 h | Passed, 7 for your builder | |
| 1,200 sq ft | 12' | 10' x 8' overhead | 25 | 6 at 8' | $21,800 | $6,000 to $18,000 | 170 to 250 h | Passed, 7 for your builder |
Each row is the starting plan as drawn, for 30 psf of ground snow, 115 mph of wind and a 36 in frost line. Materials are rounded: shelf prices plus the estimated trusses and concrete, before sales tax, delivery, labor and site work. Each plan page keeps the shelf prices, the estimate and the exact sum apart. Labor is the published range for hiring it out, a broad reference and not a quote; build time is total labor hours. Passed means the preliminary checks passed for those loads; local approval is not checked.
What they cost
About $17,100 to $21,800 in materials.
Each plan's materials list, priced line by line, lean-to included: shelf prices plus the trusses and the concrete estimated from published ranges. Hired labor is apart and only a broad reference from published price guides, not a quote.
- Lowest
- $17,100, 24x32
- Highest
- $21,800, 30x40
- Per sq ft of floor
- $18.20 to $22.24
- Labor if hired, broad reference
- $3,840 to $18,000
Excluded: sales tax, delivery, permits, site work, engineering and equipment rental
The pole barn cost guide breaks it down by group, and the pole barn cost calculator runs the same numbers for your own size.
Materials for each pole barn lean-to plan
Shelf prices read at Lowe's, Atlanta-Edgewood store, Oct 27, 2026; Menards, Columbus, Ohio store, Nov 11, 2026; Home Depot, Hamilton Mill store, Oct 8, 2026; Summertown Metals price list, Summertown, Tennessee store, Oct 13, 2026; Lowe's, Atlanta-Edgewood store, Oct 8, 2026; Best Buy Metals online store, Knoxville, Tennessee, Oct 13, 2026; Home Depot, Hamilton Mill store, Oct 13, 2026; Summertown Metals price list, Hayden, Alabama store, Oct 13, 2026; Home Depot, Hamilton Mill store, Nov 17, 2026; Tanner Bolt and Nut online store, shipped, Nov 18, 2026; Zoro.com, shipped, Nov 18, 2026; Home Depot, Bronx Terminal store, Sep 30, 2026; Home Depot, Hamilton Mill store, Oct 10, 2026; and Summertown Metals price list, Hopkinsville, Kentucky store, Oct 13, 2026, before tax and delivery. Estimates are the middle of the published ranges in HomeGuide, roof truss prices by span (Jan 2026) and Concrete Network, concrete prices (Jul 2026), read Oct 27, 2026. 30d or 60d hot-dip galvanized common nails for the post plies, budget allowance at $30.00 per 5 lb box: our budget allowance, an estimate and not a published price.
Each total is the shelf-price lines plus the common trusses, gable-end trusses, post lamination nails, concrete and ready-mix concrete slab, estimated from published ranges and kept apart on each plan page. Your supplier quotes the final price for those.
Labor if you hire it out, 24x32: Median of the published figures $5,760 for 768 sq ft at $5 to $15 per sq ft (HomeGuide, Jan 2026: $5 to $10; Angi, May 2026: $5 to $15). A sourced range for erecting a post-frame shell (posts, trusses, steel), not a quote. A broad reference from published price guides, not a quote or a forecast for your site.
The $79 builder's plan
Free to plan. $79 to build from.
Every plan above is free to open, check and price. The builder's plan is drawn from the barn you finish, for one payment. These are real sheets from the 39-sheet plan for the 30x40 pole barn.
Free
- The design in 3D, and every change you make to it
- Every preliminary check, with its rule and its source
- The materials list priced line by line
- A summary PDF of the design and its checks
$79 once
- The post layout, every post dimensioned from one corner
- Every wall framed: girts, headers and openings with heights
- The truss order sheet to hand the truss maker
- The roof frame and the steel, panel by panel
- The cut list, the shopping list with store prices and the build, step by step
You check out in the designer, with your design loaded. If the plan has an error, we fix it or refund you within 30 days. Guarantee terms.
Questions
Anything else? Write to us or read the questions about all plans.
Questions about pole barn lean-to plans
On our 30x40 pole barn with a lean-to the lean-to roof is a row of rafters, one on each post line, bolted to the main post over a ledger pair at the top and resting on the lean-to's own posts at the low edge, with purlins and steel on top. The plan's materials list has every board, the ledger and the connectors.
Your zoning sets the setback, and it differs by town and district. A lean-to widens the building, so measure from the outer edge of its roof, not from the main wall. Ask your planning or zoning office for the side and rear setbacks and any easements before you place the posts.
Harder than a shed and easier than stick framing. Our 30x40 with a lean-to comes to about 170 to 250 labor hours, roughly 11 to 16 working days for a crew of two. The hard parts are setting the posts plumb and in line and lifting the trusses; the how-to guide covers both.
The lean-to rafters bolt to the main posts over a ledger pair, and the lean-to roof stops 6 in under the main eave. If the barn already stands, its posts and pads were sized without the lean-to, so ask a builder or engineer to check them first: the designer shows the extra load as 1,546 lb on each main post on the 30x40.
Other ways to browse
Not quite the barn you picture?
Illustration
Illustration
Illustration
Your loads, your barn
Start from the 30x40. Make it yours.
Change the width, the length, the bays, the eave, the doors and your loads. The post size and depth, the purlins, the headers and the materials list follow every change. Free, no account.
Customize this design, free- Designing
- Free
- Builder's plan
- $79 once
- Account
- Not needed




